600 V Underground Secondary Distribution Cables (ICEA)

905-944-4300

Description

Standards

National : ICEA S-105-692; ICEA S-81-570

Description

Nexans Underground Secondary Distribution Cables may be used for underground secondary distribution and service entrance applications at 600 volts or less. They may be either directly buried or installed in ducts, in either wet or dry locations. These cables are designed to operate at a conductor temperature not exceeding 90°C for normal operation, 130°C for emergency overloads, and 250°C under short circuit conditions.

As a result of their enhanced mechanical properties, Nexans Ruggedized Underground Secondary Distribution Cables are especially suited for applications requiring superior resistance to abrasion, scoring and crushing.

Conductor Construction
Solid or Class B compressed concentric-lay-stranded 1350 aluminum.

Phase Conductor Insulation Material*
The insulation on the phase conductor(s) is black low-density crosslinked polyethylene.

Neutral Conductor Insulation Material*
The insulation on the neutral conductor may be either:

Black low-density crosslinked polyethylene
Black low-density crosslinked polyethylene with three extruded yellow stripes

*Note: The ruggedized construction uses an inner layer of low-density crosslinked polyethylene, with an outer layer of high-density crosslinked polyethylene.

Assembly
Multiplex constructions are twisted together with a left hand lay not greater than 60 times the outside diameter of a single phase conductor.

Markings
The insulation will bear the following surface markings:

Nexans
Year and Plant of Manufacture
Phase Conductor Size
600V
Phase identification on quadruplex cables only

Standard
Manufactured and tested to ANSI/ICEA S-105-692 (Standard for 600 Volt Single Layer Thermoset Insulated Utility Underground Distribution Cables) or ANSI/ICEA S-81-570 (Standard for 600 Volt Rated Cables of Ruggedized Design for Direct Burial Installations as Single Conductors or Assemblies of Single Conductors).

UL listing and marking for Type USE-2 is available upon request.

Characteristics

Construction characteristics
Conductor material	Aluminum
Electrical characteristics
Maximum operating voltage	600V
Usage characteristics
Maximum operating temperature	250°C

Products and services

Results

5 products available

Selected item(s): Add to favorites Apply

Part Number	Country ref.	Description
12001002	651987	2C1/0 1C2 XLP BRENAU/YS SEQFT
12001302	642587	2C4/01C2/0 SWEETBRIAR/YS SEQ
12001001	651963	2C3501C4/0XLUD600V WESLEYAN/YS
12001003	652050	3C4/01C2/0ALXLP SEQ WAKEFOREST
12001435	662160	2C3501C4/0 WESLEYAN/YS RGGD-2

Selected item(s) : Add to favorites Apply

Docs and info

UD Single Conductor 600 V

Code Word	Size AWG or kcmil (# of Wires)	Conductor Diameter		Insulation Thickness		Nominal Diameter		Approximate Net Cable Weight		Ampacity (ICEA)
		Conductor Diameter		Insulation Thickness		Nominal Diameter		Approximate Net Cable Weight		Direct Buried (Note 1)	Pole Riser Conduit (Note 2)
		inches	mm	inches	mm	inches	mm	lb / 1000 ft	kg / km	Direct Buried (Note 1)	Pole Riser Conduit (Note 2)
CORNELL/XLP	8 (7)	0.141	3.581	0.060	1.52	0.26	6.6	34	51	74	36
PRINCETON/XLP	6 (7)	0.178	4.521	0.060	1.52	0.30	7.6	47	70	97	47
MERCER/XLP	4 (7)	0.225	5.715	0.060	1.52	0.35	8.9	67	100	117	60
CLEMSON/XLP	2 (7)	0.283	7.188	0.060	1.52	0.41	10.4	97	144	154	82
KENYON/XLP	1 (19)	0.322	8.179	0.080	2.03	0.49	12.4	128	190	171	97
HARVARD/XLP	1/0 (19)	0.362	9.195	0.080	2.03	0.52	13.2	154	229	193	112
YALE/XLP	2/0 (19)	0.406	10.312	0.080	2.03	0.57	14.5	186	277	221	132
TUFTS/XLP	3/0 (19)	0.456	11.582	0.080	2.03	0.62	15.7	225	335	253	155
BELOIT/XLP	4/0 (19)	0.512	13.005	0.080	2.03	0.68	17.3	274	408	290	185
HOFSTRA/XLP	250 (37)	0.558	14.173	0.095	2.41	0.75	19.1	329	490	317	199
GONZAGA/XLP	300 (37)	0.611	15.519	0.095	2.41	0.81	20.6	385	573	349	223
RUTGERS/XLP	350 (37)	0.660	16.764	0.095	2.41	0.85	21.6	439	534	381	248
DARTMOUTH/XLP	400 (37)	0.706	17.932	0.095	2.41	0.90	22.9	493	731	410	272
BROWN/XLP	450 (37)	0.749	19.025	0.095	2.41	0.94	23.9	547	814	439	295
EMORY/XLP	500 (37)	0.789	20.041	0.095	2.41	0.98	24.9	601	894	464	318
DUKE/XLP	600 (61)	0.866	21.996	0.110	2.79	1.09	27.7	725	1079	514	355
FURMAN/XLP	700 (61)	0.935	23.749	0.110	2.79	1.16	29.5	830	1235	549	386
SEWANEE/XLP	750 (61)	0.968	24.587	0.110	2.79	1.19	30.2	883	1314	567	403
FORDHAM/XLP	1000 (61)	1.118	28.397	0.110	2.79	1.34	34.0	1144	1702	665	492
THESE AMPACITY VALUES ARE NOT TO BE USED FOR NEC. Notes: - Where stated, “nominal” and “approximate” values are provided for information purposes only and are subject to standard manufacturing tolerances. 1. For non-NEC applications, based on the following installation parameters: - 90°C conductor temperature - 20°C earth ambient temperature - earth thermal resistivity (RHO) of 90°C cm / W - 36 inch depth of burial - 100% load factor 2. For non-NEC applications, pole riser conduit ampacities are based on the following installation parameters: - 90°C conductor temperature - 40°C ambient air temperature - No sun (shaded) - No wind - Non-metallic duct - 100% load factor

UD Cable Duplex 600 V

Code Word (Black Neutral) (Note 1)	Phase Conductor			Neutral Conductor			Cable				Ampacity (ICEA)
	Size AWG or kcmil (# of wires)	Insulation Thickness		Size AWG or kcmil (# of wires)	Insulation Thickness		Nominal Diameter		Approximate Net Weight		Direct Buried (Note 2)	Pole Riser Conduit (Note 3)
	Size AWG or kcmil (# of wires)	inches	mm	Size AWG or kcmil (# of wires)	inches	mm	inches	mm	lb / 1000 ft	kg / km	Direct Buried (Note 2)	Pole Riser Conduit (Note 3)
ALCORN/XLP	8 (1)	0.060	1.52	8 (1)	0.060	1.52	0.50	12.7	64	95	75	36
BARD/XLP	8 (7)	0.060	1.52	8 (7)	0.060	1.52	0.53	13.5	67	100	75	36
*CLAFLIN/XLP	6 (7)	0.060	1.52	6 (7)	0.060	1.52	0.60	15.2	91	135	97	47
	4 (7)	0.060	1.52	6 (7)	0.060	1.52	0.65	16.5	110	164	123	60
DELGADO/XLP	4 (7)	0.060	1.52	4 (7)	0.060	1.52	0.69	17.5	129	192	123	60
CEDARCREST/XLP	2 (7)	0.060	1.52	4 (7)	0.060	1.52	0.75	19.1	157	234	160	82
EVERETT/XLP	2 (7)	0.060	1.52	2 (7)	0.060	1.52	0.81	20.6	186	277	160	82
FINDLAY/XLP	2/0 (19)	0.080	2.03	2/0 (19)	0.080	2.03	1.14	29.0	374	557	233	132
HANOVER/XLP	4/0 (19)	0.080	2.03	4/0 (19)	0.080	2.03	1.35	34.3	552	821	301	185
GLENVILLE/XLP	350 (37)	0.095	2.41	350 (37)	0.095	2.41	1.71	43.4	884	1316	395	248
THESE AMPACITY VALUES ARE NOT TO BE USED FOR NEC. Notes: - Where stated, “nominal” and “approximate” values are provided for information purposes only and are subject to standard manufacturing tolerances. 1. For yellow stripes on neutral, add "EYS" to black neutral code word (eg. "CLAFLIN / XLP / EYS"). 2. For non-NEC applications, based on the following installation parameters: - 90°C conductor temperature - 20°C earth ambient temperature - earth thermal resistivity (RHO) of 90°C cm / W - 36 inch depth of burial - 100% load factor 3. For non-NEC applications, pole riser conduit ampacities are based on the following installation parameters: - 90°C conductor temperature - 40°C ambient air temperature - No sun (shaded) - No wind - Non-metallic duct - 100% load factor *STOCKED ITEM All other products require approval. Speak to your Inside Sales Rep.

UD Cable Triplex 600 V

Code Word (Black Neutral) (Note 1)	Phase Conductor			Neutral Conductor			Cable				Ampacity (ICEA)
	Size AWG/kcmil (# of wires)	Insulation Thickness		Size AWG (# of wires)	Insulation Thickness		Nominal Diameter		Approximate Net Weight		Direct Buried (Note 2)	Pole Riser Conduit (Note 3)
	Size AWG/kcmil (# of wires)	inches	mm	Size AWG (# of wires)	inches	mm	inches	mm	lb / 1000 ft	kg / km	Direct Buried (Note 2)	Pole Riser Conduit (Note 3)
ERSKINE/XLP	6 (7)	0.060	1.52	6 (7)	0.060	1.52	0.65	16.5	143	213	97	47
*VASSAR/XLP	4 (7)	0.060	1.52	4 (7)	0.060	1.52	0.75	19.1	202	301	123	60
*STEPHENS/XLP	2(7)	0.060	1.52	4 (7)	0.060	1.52	0.83	21.4	262	390	160	82
RAMAPO/XLP	2 (7)	0.060	1.52	2 (7)	0.060	1.52	0.88	22.4	292	435	160	82
*BRENAU/XLP	1/0 (19)	0.080	2.03	2 (7)	0.060	1.52	1.05	26.7	407	606	205	112
BERGEN/XLP	1/0 (19)	0.080	2.03	1/0 (19)	0.080	2.03	1.13	28.7	465	691	205	112
*CONVERSE/XLP	2/0 (19)	0.080	2.03	1 (19)	0.080	2.03	1.17	29.7	504	750	233	132
HUNTER/XLP	2/0 (19)	0.080	2.03	2/0 (19)	0.080	2.03	1.23	31.2	563	838	233	132
HOLLINS/XLP	3/0 (19)	0.080	2.03	1/0 (19)	0.080	2.03	1.27	32.3	610	908	264	152
ROCKLAND/XLP	3/0 (19)	0.080	2.03	3/0 (19)	0.080	2.03	1.34	34.0	682	1015	264	152
*SWEETBRIAR/XLP	4/0 (19)	0.080	2.03	2/0 (19)	0.080	2.03	1.38	35.1	741	1103	301	185
MONMOUTH/XLP	4/0 (19)	0.080	2.03	4/0 (19)	0.080	2.03	1.46	37.1	831	1237	301	185
PRATT/XLP	250 (37)	0.095	2.41	3/0 (19)	0.080	2.03	1.53	38.9	890	1324	329	199
*WESLEYAN/XLP	350 (37)	0.095	2.41	4/0 (19)	0.080	2.03	1.72	43.7	1160	1726	395	248
HOLYOKE/XLP	500 (37)	0.095	2.41	300 (37)	0.095	2.41	2.00	50.8	1596	2375	475	305
RIDER/XLP	500 (37)	0.095	2.41	350 (37)	0.095	2.41	2.03	51.6	1652	2458	475	305
FAIRFIELD/XLP	750 (61)	0.110	2.79	500 (37)	0.095	2.41	2.42	61.5	2383	3546	589	402
THESE AMPACITY VALUES ARE NOT TO BE USED FOR NEC. Notes: - Where stated, “nominal” and “approximate” values are provided for information purposes only and are subject to standard manufacturing tolerances. 1. For yellow stripes on neutral, add "EYS" to black neutral code word (eg. "SWEETBRIAR / XLP / EYS"). 2. For non-NEC applications, based on the following installation parameters: - 90°C conductor temperature - 20°C earth ambient temperature - earth thermal resistivity (RHO) of 90°C cm / W - 36 inch depth of burial - 100% load factor 3. For non-NEC applications, pole riser conduit ampacities are based on the following installation parameters: - 90°C conductor temperature - 40°C ambient air temperature - No sun (shaded) - No wind - Non-metallic duct - 100% load factor *STOCKED ITEM All other products require approval. Speak to your Inside Sales Rep.

UD Cable Quadruplex 600 V (ICEA)

Code Word (Black Neutral) (Note 1)	Phase Conductor			Neutral Conductor			Cable				Ampacity (ICEA)
	Size AWG or kcmil (# of wires)	Insulation Thickness		Size AWG (# of wires)	Insulation Thickness		Nominal Diameter		Approximate Net Weight		Direct Buried (Note 2)	Pole Riser Conduit (Note 3)
	Size AWG or kcmil (# of wires)	inches	mm	Size AWG (# of wires)	inches	mm	inches	mm	lb / 1000 ft	kg / km	Direct Buried (Note 2)	Pole Riser Conduit (Note 3)
DYKE / XLP	2 (7)	0.060	4.52	4 (7)	0.060	1.52	0.94	23.9	332	494	160	82
*WAKE FOREST / XLP	4/0 (19)	0.060	2.03	2/0 (19)	0.060	2.03	1.57	39.9	959	1427	301	185
SLIPPERY ROCK / XLP	350 (37)	0.060	2.41	4/0 (19)	0.060	2.03	1.95	49.5	1529	2275	395	248
THESE AMPACITY VALUES ARE NOT TO BE USED FOR NEC. Notes: - Where stated, “nominal” and “approximate” values are provided for information purposes only and are subject to standard manufacturing tolerances. 1. For yellow stripes on neutral, add "EYS" to black neutral code word (eg. "DYKE / XLP / EYS"). 2. For non-NEC applications, based on the following installation parameters: - 90°C conductor temperature - 20°C earth ambient temperature - earth thermal resistivity (RHO) of 90°C cm / W - 36 inch depth of burial - 100% load factor 3. For non-NEC applications, pole riser conduit ampacities are based on the following installation parameters: - 90°C conductor temperature - 40°C ambient air temperature - No sun (shaded) - No wind - Non-metallic duct - 100% load factor *STOCKED ITEM All other products require approval. Speak to your Inside Sales Rep.

600 V Underground Secondary Distribution Cables (ICEA)

Contact

Description

Standards

Description

Characteristics

Products and services

Results

Docs and info

UD Single Conductor 600 V

UD Cable Duplex 600 V

UD Cable Triplex 600 V

UD Cable Quadruplex 600 V (ICEA)

You must be registered to access this service.
Sign in with your Nexans account :

Your Account

600 V Underground Secondary Distribution Cables (ICEA)

Contact

Description

Standards

Description

Characteristics

Products and services

Results

Docs and info

UD Single Conductor 600 V

UD Cable Duplex 600 V

UD Cable Triplex 600 V

UD Cable Quadruplex 600 V (ICEA)

Berk-Tek

Legal

The TEK Center

Share Price

You must be registered to access this service.Sign in with your Nexans account :

Your
Account

You must be registered to access this service.
Sign in with your Nexans account :